Characterization and Photo-catalytic Efficiency of MnFe2O4/Zn2SiO4 for Aniline Degradation Using Box-Behnken Experimental Design and Simulated Solar Radiation

Document Type : Research Paper

Authors

Department of Chemistry, Arak Branch, Islamic Azad University, Arak 086, Iran

Abstract

In this research, Zn2SiO4 as a support and MnFe2O4 as a main photo-catalyst were individually syn-thesized and MnFe2O4 was fixed on Zn2SiO4 with solid state dispersion method. MnFe2O4 nano pho-to-catalyst was synthesized by co-precipitation method and
reflux condition for 12 hours at 85°C in the presence of urea. For identification of catalysts
Fourier-transform infrared (FTIR) spectroscopy, Field emission scanning electron microscopy (FESEM), Energy-dispersive X-ray spectroscopy (EDXS), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray fluorescence (XRF) and Brunauer-Emmett-Teller (BET) techniques were used. The size of MnFe2O4 was determined about 15 nm after the fixation on the Zn2SiO4. The photo-catalytic efficiency of MnFe2O4/Zn2SiO4 was checked for degradation of aniline aqueous solu-tion utilizing the irradiation of a 1 kW Xe lamp fitted with the AM1.5 filter (to simulate the solar light spectrum) in the presence of H2O2. Degradation process was modeled and optimized successfully ap-plying response surface methodology (RSM) according to Box-Behnken designs. Experiment results were showed that initial concentration of aniline=5.5 ppm, H2O2 initial concentration=5.3 mM, pH=11 and nano photo-catalyst amount =0.4 g/L are optimal conditions and the degradation effi-ciency in this condition achieved is 96%. In the optimum conditions, arrangement of (MnFe2O4/Zn2SiO4)> (MnFe2O4)> (Zn2SiO4) was obtained for efficiency of photo-catalytic degrada-tion of aniline in aqueous solution. Decomposition kinetic equation determined pseudo first order and k=0.0407.

Keywords


INTRODUCTION

Aniline, one of the aromatic organic compounds derived from material oil refining, is widely used in different industries to produce various materials such as polymer, oligomer, Isocyanides, agricultural pesticides, dyes and pigments [1]. This material has always brought about ecological problems of ground waters and surface waters. In addition, various toxic compounds are produced by aniline reaction to oxygen [2]. There are various methods such as physical treatment (adsorption on activated carbon, electro-dialysis and membrane), chemical treatment (chemical precipitation, photo-catalytic processes), biological for the purification of waters containing a mixture of organic and inorganic compounds [3]. Among these methods, the photo-catalytic method is vital because of the complete removal of pollutants and their conversion to non-toxic materials such as CO2, H2O and N2 through the advanced oxidation process (AOP) [4]. So far, many studies have been done toremove aniline by kind of photo-catalyst such as TiO2, SnO2, Cr/ZnO and CuO [5-12] ( Summarized in Table 1) in which not only mineralization of aniline and intermediates have not happened completely (processes proved to require a lot of time) but also photo-catalyst isolation has been difficult.

In addition, the percentage of contamination is low and most importantly, photo-catalysts are not commercialized (Table 1). For example, ortho and para-aminophenol intermediates were formed in the process of aniline removal using titanium dioxide in the pH=12 and 84.2 percent of aniline is converted to H2O and CO2 after 240 minutes [5].

Poly-functional oxide nanoparticles such as ABO3 and AB2O4 spinel seem to have magnetic and photo-catalytic properties. Spinel ferrites, AFe2O4 (A=Mn, Mg, Zn, Co, Fe etc.) have exclusive features and functionality to remove various contaminants from water and wastewater (Das, 13). Among the spinel ferrites, manganese ferrite spinel was chosen as a main catalyst because it has narrow band-gap and multiple oxidation states [14]. In addition, its initial raw materials are abundant, inexpensive and available. The researches have shown that these compound preparation methods are diverse [15,16].

These methods are not applicable due to the complexity of the preparation process, high cost, high consumption time, high reaction temperature, environmental constituents and environmental problems. On the other hand, properties and performance of the catalyst are influenced by the raw materials and the manufacturing process. Due to these problems, MnFe2Owas synthesized using co-precipitation method to produce nano particles (NPs), to reduce cost, to increase the degradation rate, to create maximum efficiency and minimum ecological problems. To prevent the ecological impact on NPs and to facilitate their collection to reuse catalyst, utilizing magnetic spinels (MnFe2O4) became the primary focus of the research [13,15]. The separation of the catalyst from water is an inevitable problem. Stabilizing the catalysts on the base, in addition to increasing the active surface and facilitating the separation of the catalyst from the water, improves their stability. In this research, Zn2SiO4 was used a catalyst base because of it has chemical and thermal stability, insolubility in water and proper surface properties [13,15,17]. Therefore, MnFe2O4/Zn2SiO4 was synthesized as a new and effective photo-catalyst. EDXS, XRD, XRF, FESEM, BET and FTIR techniques were used to identify synthesized particles. The processes of aniline degradation in the presence of MnFe2O4 / Zn2SiO4 and the simulation of sunlight (a 1 kW Xe lamp fitted with an AM1.5 filter) was used to obtain the catalyst performance.

With stabilizing MnFe2O4 on Zn2SiO4 (as a new base) was produced unique catalyst (MnFe2O4/Zn2SiO4) for aniline degradation.

Although MnFe2O4 has been used to remove many pollutants in photocatalytic process, MnFe2Oand MnFe2O4/Zn2SiO4 has not been reported to remove aniline. This is exactly the novelty of this study.

Degradation processes were modeled, and affective factors such as aniline initial concentration, H2O2 initial concentration, pH and the amount of nano photo-catalyst were optimized successfully applying RSM according to Box-Behnken design [18]. The kinetics of aniline photo-degradation reactions to presence of MnFe2O4/Zn2SiO4, MnFe2O4 and Zn2SiOwere investigated under optimum condition and their photo-catalytic efficiency were compared. Repeatability of the MnFe2O4/Zn2SiO4 efficiency was demonstrated by performing the aniline degradation test five times under optimum condition using depreciated photo-catalyst.

EXPERMENTAL

Materials and Apparatus

Chemical reagents include zinc sulfate (ZnSO4.7H2O), manganese nitrate (Mn(NO3)2.4H2O), iron nitrate (Fe(NO3)3.9H2O), NaOH, urea, aniline and silicon dioxide (SiO2=99.5%w/w, 10-20 nm particle size (BET)) were purchased from Sigma Aldrich Company. Other materials such as ethanol, hydrogen peroxide (35% w/w) were taken from Merck Company.

The Infrared spectra of all materials were taken with Fourier transform infrared spectroscopy (Spectrum Two FT-IR Spectrometer, Perkin-Elmer). XRD analysis of the samples was done applying an X-ray spectrometerX27-mini diffract-meter. XRF and BET analysis of MnFe2O4/Zn2SiO4 were done utilizing X-ray fluorescence ARL PER FORM’X and BELSORP-mini II, Bell Japan, respectively. The morphology, elemental mapping of the samples and the particles size were determined employing Field emission scanning electron microscopy (FESEM, XL-30, Philips) and transmission electron microscopy (TEM, Zeiss-EM10C-100 KV, Germany). Energy Dispersive X-ray Spectroscopy (EDXS, Philips) was used to determine the type and the percentage of elements. The UV-Vis spectra of the aniline in aqueous media were recorded by Agilent 8453 UV-visible spectrophotometer. The photo-catalytic decomposition of aniline was performed in the one-liter batch photo-reactor and 1 kW Xe lamp fitted with AM1.5 filter (to simulate the solar light spectrum).

Preparation of Zn2SiO4, MnFe2O4 and MnFe2O4/Zn2SiO4

To prepare Zn2SiONPs in correspondence with documents [17], 0.1 mole of [ZnSO4.7H2O] was completely dissolved in 100 ml distilled water. Then, 100 ml NaOH, 0.2 moles were added drop by drop to zinc sulfate solution and stirred at 80 °C. The solution was cooled to ambient temperature. Precipitated Zn(OH)was separated from the solution by centrifuge, it washed with distilled water and it dried at 100 °C for 12 h.

0.2 mole Zn(OH)2 and 0.1 mole silica powder with high purity were added to 200 ml distilled water and this mixture was stirred for 4 h at 80 °C. Precipitate was centrifuged and dried at 80 °C in oven and finally calcined at 1050 °C.

Based on previous research, MnFe2O4 NPs were synthesized in the urea aqueous solution to the reflux condition. To do this, 0.2 mole of (Fe(NO3)3.9H2O) and 0.1 mole of (Mn(NO3)2.4H2O) were dissolved in 200 ml water and 250 ml of 0.4 molar urea was added to this solution. This solution was heated on the water bath at 85°C for 12 h in the reflux condition. Precipitate was separated by centrifuge and washed with water and ethanol (respectively) several times. It was dried at 80°C in oven and calcined at 990 °C [19,20].

To prepare MnFe2O4/Zn2SiO4, MnFe2O4 nanoparticles were mechanically mixed with Zn2SiO4 (1:3 w/w %) in the presence of ethanol by agate pestle and mortar. This homogeneous mixture was dried at 110 °C in oven for 2 h and calcined at 1050 °C in the furnace for 5 h. Precipitate was sieved employing 100 mesh standard sieves.

Design of Experiment (DOE)

Design of experiment by Box-Behnken method has been used to obtain the minimum test required to obtain the effect of variables and relationship between variables on the percentage of aniline degradation also it used for optimization and mathematical modeling [19].

According to Box-Behnken design (using a randomized method) with four variables and three levels for each variable, 27 tests were determined.

Variable levels were determined corresponding to Table 2.

The Minitab 17 statistical software was used to design the Box-Behnken. Experimental conditions were performed based on the design matrix (Table 3). The pH of solutions was modified by NaOH and H2SO4 (0.01 M). All of the experiments were performed with 1 liter of aqueous solutions to the batch reactor with stirring at ambient temperature. In each operation, photo-catalysts were added to aqueous solutions and maintained in the dark space for 30 minutes before irradiation. Then H2O2 with specific concentration was added to solution and maintained under simulated solar light irradiation (1 kW Xe lamp fitted with AM1.5 filter) for 120 minutes. The absorbance of aniline solutions before and through irradiation was analyzed applying UV-Vis spect­­rophotometer at 230 nm, within 120 minutes at 10-minute intervals. The percentage of aniline degradation was calculated by the equation (1) for 27 experiments separately.

 (1)

Where A0 is absorption amounts to maximum absorption wavelength (230 nm) at t=0 (before irradiation), Ais absorption amounts to at maximum absorption wavelength after t minute irradiation.

The most important parameters such as probability values (P-values), standard deviation of the residuals (S), R2, adjusted R2 and predicted Rvalues were determined by variance analysis (ANOVA). The adequacy of the model was checked by residual plots of degradation. Then, response optimizer was applied to recognize the best operating conditions or global solutions to optimize the aniline degradation, to decrease costs, to increase sensitivity of factors and desirability.

In the optimum condition, photo-catalytic efficiency and kinetic of MnFe2O4/Zn2SiO4, MnFe2O4 and Zn2SiO4 were compared.

The catalyst performance was also studied after five times the experiment in optimal conditions.

RESULTS AND DISCUSSION

Characterization of MnFe2O4/Zn2SiO4 photo-catalyst

X-Ray Diffraction and X-ray Fluorescence analysis

The XRD patterns of the synthesized samples (MnFe2O4, Zn2SiOand MnFe2O4/Zn2SiO4) were taken as follows (Fig. 1).

The comparison of these diffraction patterns with the results taken by other researchers confirmed the synthesis of MnFe2O4/Zn2SiO4 [19, 21-24]. The average size of MnFe2Osupported on Zn2SiO4 based on the collected data from XRD and the use of Debye-Scherrer equation [23] was obtained about 19.1nm.

XRD sharp and intense peaks within diffraction patterns of synthetic materials demonstrated that there is a high degree of crystallinity in all synthetic NPs. Also, MnFe2Ostabilization on Zn2SiOis proved by comparison of diffraction pattern of MnFe2O4/Zn2SiO4 with those of MnFe2Oand Zn2SiO4. The presence of Zn2SiO4 and MnFe2O4 peaks in XRD patterns of MnFe2O4/Zn2SiO4 indicate that the crystalline structure of these materials is not altered in the catalyst.

Furthermore, elemental and oxide compositions of MnFe2O4/Zn2SiO4, which are shown in Table 4, were determined by XRF. These results demonstrate that atomic ratios are proportional to MnFe2O4/Zn2SiOstructure.

Fourier transforms infrared spectroscopy

FTIR spectra of MnFe2O4/Zn2SiO4, MnFe2Oand Zn2SiO4 are displayed in Fig. 2 and all the absorption bands and their assignment for MnFe2O4/Zn2SiOare summarized in Table 5. The observing index peaks of MnFe2Oand Zn2SiOin MnFe2O4/Zn2SiOspectrum, confirm synthesis of MnFe2O4/Zn2SiOnanoparticles.

The peaks at 578 and 460 cm-1 in spectrum correspond respectively to deformation
vibrations of Fe-O and Mn-O in tetrahedral and octahedral coordination compounds in the spinel structure. Moreover, 1630 and 3435 cm-1 bands are related to O-H bending and stretching vibration, a fact which indicates water and the absorbed OH at the catalyst surface [25-27]. Also, position of 3436 and 1630 cm-1 bands are correlated with bonding and stretching vibrations of O-H in Si-OH [22,23]. The 1150 cm-1 bond is related to Mn-O-H bending vibration. The 978, 933 and 902 cm-1 bonds correspond to asymmetric stretching vibrations and 870 cm-1 peak is related to symmetric stretching vibrations of Si-O in SiO4 units. Symmetric and asymmetric stretching vibrations of ZnO in ZnO4 units appear at 578 and 616 cm-1, respectively [23,24]. The results of FTIR analysis demonstrate that there is not any impurity in the crystal lattice and also it exhibits that the calcinations temperature for preparation of MnFe2O4/Zn2SiO4 is suitable.

FESEM, EDXS and TEM analysis

The morphology of MnFe2O4/Zn2SiO4, (Figs. 3(a-c)) was obtained by FESEM. The exact investigation of the magnified pictures (Figs. 3(b) and (3c)) reveals the agglomeration of NPs. Considering that the formation and growth of these NPs are based on the reaction of urea, manganese nitrate and iron nitrate precursors under hydrolysis and reflux condensation in water (based on reactions (2-6)), probably, the agglomeration of NPs and the formation of dense grains are due to solvent polarity and high calcination temperature.

To acquire more information, the analysis of Energy Dispersive X-ray spectroscopy (EDXS) of MnFe2O4/Zn2SiO4 was taken. Fig. 3(d) indicates the EDXS spectra and the elemental composition of MnFe2O4/Zn2SiO4. The EDXS analysis of MnFe2O4/Zn2SiO4 spectrum reveals the presence of Fe, Mn, Zn, Si and O elements.

Fig. 4 (a, b) shows the morphology and core-shell structure of MnFe2O4/Zn2SiO4. Magnified images to demonstrate that MnFe2O4 shell with a thickness of less than 15 nm formed into the Zn2SiO4 core.

Elemental mapping of iron, manganese, zinc, silica and oxygen in MnFe2O4/Zn2SiO4 are shown in Fig. 5(b-f) by green, orange, red, blue and yellow points, respectively. Spatial distribution, compositional zonation and the presence of the elements in MnFe2O4/Zn2SiOis characterized by these colored points.

 (2)

 (3)

 (4)

 (5)

 (6)

BET analysis

BET analysis for synthesized MnFe2O4/Zn2SiOwas performed by determining the amount of adsorption and desorption of N2 gas at 77 K (Fig. 6). Amount of “means pores area” and “means pores volume” were determined about 52.79 m2 g-1 and 0.058 cm3 g-1respectively. These amounts indicate the notable physical interaction of N2 gas with the surface of NPs molecules. Fig. 6 (a) shows that the isotherm structure is similar to that of the IV type isotherm. Also, hysteresis displays the existence of meso pores with cylindrical structure of NPs (Fig. 6(a)) [28]. Pore size distribution was found by Barclay James Harvest (BJH) plot (Fig. 6(c)). As the results present, the mean pore diameter is about 4.43 nm.

Modeling using a Box-Behnken design with RSM

Analysis of variance (ANOVA) and model fitting

The RSM was used to understand and optimize important factors, to determine and refine the model [18]. The Box-Behnken design, one of response surface design (RSD) was used because this method needs fewer tests and all the factors are not placed simultaneously at a high or low level and the coefficients are estimated to be the second order. Also, the Box-Behnken design, as compared to other methods, reduces the number of tests without reducing accuracy [18]. According to Box-Behnken design with four factors and three levels, cases such as experimental conditions, factor combinations and run-order of 27 experiments were determined by randomizing corresponding to Table 3 [18].

In the photo-catalytic process, the semiconductor of MnFe2O4/Zn2SiO4 was used as main catalyst along with simulated radiation of the solar light on the photo-catalyst surface. In order to determine the efficiency of the photo-catalyst, aniline degradation process (27 experiments) was performed corresponding to design matrix (Table 3). In photo-catalytic degradation process, corresponding to Fig. 7, light radiation takes effect on the surface of the semiconductor and electrons are transferred from the valence band to the conductive band. Therefore, the holes in the valence bands and the electrons in conducting layer are created. Holes are strongly oxidizer. Thus, hydroxyl ion from NaOH and H2O molecules reacts with photo-catalyst valance bond holes. These steps redound to the formation of hydroxyl radicals. Electrons in the valence band react with dissolved oxygen, and consequently superoxide radicals are produced. Then superoxide radicals after some steps are converted to hydroxyl radicals. Superoxide and hydroxyl radicals are very reactive. Hydrogen peroxide can increase the production of radicals. Also, the formation of hydroxyl radicals is increased by the change of pH and catalyst. Accordingly, aniline is degraded and converted to CO2 and H2O by active radicals after some steps. As a consequence, percentages of aniline degradation for 27 experiments are affected by type, level and combination of factors.

After calculating the percentage of aniline degradation by equation 1 (for 27 experiments) and performing an analysis of Box-Behnken design, analysis of variance (ANOVA) was investigated. Studying the amounts of P-values in the ANOVA table for any variable (section a, Table 6) shows that the impact on second order factors of x4x4 and x3x3 is insignificant because they have P-values>0.05. In this research, confidence level has been chosen equal to α=0.05. Therefore, the effects that have P-values>0.05 are insignificant and vice versa, So second order terms with large P-values were omitted and the analysis response surface design was once again repeated and the result of ANOVA was recorded in section b of Table 6. In the models listed in Table 7, comparing P-values of lack of fits (after removing insignificant terms) appraises the fit of the model. According to Table 7, the P-values of the full quadratic model are more than 0.05; thus, this model accurately fits the data. Since the amounts of P-values are less or equal to 0.05 in other models, they couldn’t cover the data properly. The statistical parameters such as adjusted R2 and standard deviation of the residuals in full quadratic model prove the suitability of full quadric model in fitting the data of response surface (compared to the other models). On the other hand, the amounts of P-values for interaction factors (x1x2, x1x3, x1x4, x2x3, x2x4 and x3x4) and second order term (x1x1, x2x2) to express the curvature of response surface.

The R2 value points out that the predictors (factors) illustrate 98.06% of the variance in aniline degradation yield. The adjusted R2 is 96.40%, a fact which explains the number of effects on the model. Both value to indicate that the model is well suited to the data. The amount of the predicted R2 is 92.08%. There are no over fit values of the model, so it has sufficient predictive power.

The standard deviation of the residual in final regression is equal to 1.05677. This shows that actual data have a 1.05677 standard distance from the regression line or the predicted value. Also, small amount of S indicates that the model is suitably enough.

Model modification, adequacy checking and optimization

After determining the significant and insignificant effects, insignificant factors including x4x4 and x3x3 were removed in order to improve the model. The estimated regression coefficients for the degradation of aniline were acquired by equation (7-8) based on un-coding data. Where Y is aniline degradation yields (response), xi and xj are factors, β0 is overall mean, βi and βij are regression coefficients and ɛ is random error with normal distribution (mean = 0 and standard distribution of δ).

Omitting insignificant factors, R2 lowered slightly (from 98.10% to 98.06%) and the amount of adjusted R2, which is more important, increased a little (from 95.89% to 96.40%). The predicted R2, which is an important parameter in predicting response from new observations, changed from 89.83% to 92.08%. The model with bigger value of predicted Rhas larger predictive ability for new observations. Also, the reduction of the sum of squares of the prediction error (PRESS) from 82.128 to 63.969 through removing the insignificant factors indicates greater predictive ability of the model, too.

The equation (8) indicates that aniline concentration and pH have second order effects, whereas initial concentration of H2O2 and the amount of MnFe2O4/Zn2SiO4 photo-catalyst have just linear effects.

The distribution and the independence of the residuals were studied to check the adequacy of the model (Fig. 8). The residuals, which are the difference between the test response and the predicted response, are normal if the points are near the regression line (Fig. 8(a)). Regarding that the residuals against fitted values in Fig. 8(b) are completely random and scattered; therefor, residuals are independent. This means that the residuals have non-constant variance.

Fig. 8(c) exhibits a histogram of the residuals. It indicates that the errors are random and there are no data collection orders for residuals. Structure of Fig. 8(d) approves that residuals do not have correlation with each other. Thus, all of the mentioned interpretations confirm that ANOVA table (Table 6) is reliable and the model can predict aniline degradation yields ± 1.05677 with a 95% confidence level (confidence interval).

 

 (7)

 

Finally, response optimizer was applied to recognize the best operating conditions in order to optimize the aniline degradation, decrease cost, increase sensitivity of factors and desirability. Desirability values (D), according to optimization parameters, became equal to 0.913. Optimal factors for aniline, H2O2, pH and catalyst were determined equal to 5.5 ppm, 5.3 mM, 11 and 0.4 g/L, respectively. These factor settings are the best factor levels, which is called global solution. Also predicted value of the yield of aniline degradation became equal to 96%.

Kinetics of photo-catalytic degradation of aniline

Fig. 9 displays the plot of Ln(A0/A) versus reaction time for aniline decomposition in
optimum condition with different NPs. The linearity of the plot suggests that the photo-degradation reaction approximately follows the pseudo first order kinetics. The efficiency of MnFe2O4, Zn2SiO4 and MnFe2O4/Zn2SiO4 in relation to each other was compared in optimum conditions and the arrangement of (MnFe2O4/Zn2SiO4)> (MnFe2O4)> (Zn2SiO4) was obtained. The results of the kinetic experiments indicate that the activity of MnFe2O4 photo-catalyst has increased due to stability on the Zn2SiO4 as a base. The increase in the effective surface of the catalyst and the possibility of absorbing contaminants on the catalyst can be due to the increase of the activity.

In order to study the reproducibility of the efficiency of final photo-catalyst, all the depreciated NPs of MnFe2O4/Zn2SiO4 were collected, washed, dried and were reused for degradation of a new aniline solution to optimal conditions. This process was repeated five times continuously. Comparing the efficiency of degradation in each stage signifies that the activity of degradation nano photo-catalyst is considerably reproducible (Fig. 10).

CONCLUSION

In this research, MnFe2Osupported on Zn2SiO4 was successfully produced via hydrolysis apply urea and co-precipitation method. Various techniques, such as XRD, XRF, FTIR, FESEM, EDXS, TEM and BET were employed to specify Characteristics of new MnFe2O4/Zn2SiO4 photo-catalyst. The results derived from of these techniques presented that the synthesized particles are in nano-scale and have a suitable surface area. The
formation of the MnFe2O4 shell on the Zn2SiO4 core with a thickness of less than 15 nm was also confirmed. The efficiency of the MnFe2O4/Zn2SiO4 was corroborated through the photo-catalytic degradation process of aniline under simulated solar radiation; such efficiency is due to its nano-porous core–shell structure. The study revealed that DOE using RSM with Box-Behnken design approach is an excellent technic to specifying significant parameters, interaction factors and empirical model to optimize the aniline
degradation, to decrease costs, to increase the sensitivity of factors and desirability. As presented, the statistical parameters such as adjusted R2 (96.40%) and standard deviation of the residuals (1.05677) in full quadratic model affirmed the suitability of full quadric model in fitting the data. Moreover, the best operating conditions for factors of aniline, H2O2, catalyst and pH were obtained something equal to 5.5 ppm, 5.3 mM, 0.4 g L-1 and 11, respectively. Besides, the predicted value for photo-catalyst efficiency and desirability in aniline degradation also were achieved, equal to 96% and 0.913, in sequence. The efficiency of synthetic NPs in the following arrangement MnFe2O4/Zn2SiO4> MnFe2O4> Zn2SiO4 demonstrated the influence of base (Zn2SiO4) on activity of Mnfe2O4 due to the increase in the surface area of the photo-catalyst and the fast transfer of photoelectrons.

After five times comparing the efficiency of the depreciated photo-catalyst of MnFe2O4/Zn2SiO4 it indicated that the activity of nano photo-catalyst is considerably reusable, effective and efficient. Therefore, based on the evidence obtained, the development of studies and the use of MnFe2O4/Zn2SiO4 photo-catalyst in removal of other aromatic pollutants are recommended.

ACKNOWLEDGEMENTS

The authors appreciatively acknowledge Islamic Azad University, Arak branch, for providing facilities. This research did not receive any specific grant from funding agencies in the public, commercial, or not-for-profit sectors.

CONFLICT OF INTEREST

The authors declare that there are no conflicts of interest regarding the publication of this manuscript.

ABBREVIATIONS

Adj. MS Adjusted mean squares

Adj. RAdjusted R square

ANOVA Analysis of variance

Adj SS Adjusted sum of squares

AOP Through the advanced oxidation process

BET Brunauer–Emmett–Teller

BJH Barclay James Harvest

Deg% Percentage of aniline degradation

D Desirability value

DF Degree of freedom

DOE Design of experiment

EDXS Energy-dispersive X-ray spectroscopy

FESEM Field emission scanning electron microscopy

FTIR Fourier-transform infrared spectroscopy

F F-value

MRI Magnetic resonance imaging

MWCNT Multi-walled carbon nanotubes

NPs Nano particles

PRESS Prediction error

Pred. RPredicted R square

P P-values (probability value)

RSD Response surface design

RSM Response surface methodology

PSO Pseudo first order

RR square

Seq. SS Sequential sum of squares

S Standard deviation of the residuals

UV-Vis Ultraviolet–visible 

XRD X-ray diffraction

XRF X-ray fluorescence

Y Aniline degradation yield (Response)

 

 
13. Das I, Ansari SA. Nanomaterials in Science and Technology. 2009; 68: 657-667.
18. Myers RH, Montgomery DC. Response surface methodology: process and product optimization using designed experiments: Wiley New York; 1995.
21. Sam S, Nesaraj AS. Preparation of MnFe2O4 nano-ceramic particles by soft chemical routes. Int J Appl Sci Eng. 2011;9(4):223-239.
23. Lukić S, Petrović D, Đačanin L, Marinović-Cincović M, Antić Ž, Krsmanović R, et al. Gel combustion synthesis of transition metal ions doped Zn2SiO4 powder. Journal of Optoelectronics and Advanced Materials. 2008;10(10):2748-2752.
27. Zipare K, Dhumal J, Bandgar S, Mathe V, Shahane G. Super-paramagnetic manganese ferrite nanoparticles: synthesis and magnetic properties. Journal of Nano-science and Nano-engineering. 2015;1(3):178-182.