Document Type : Research Paper
Authors
1 Department of solid state Physics, University of Mazandaran, Babolsar, Iran
2 Nanomedicine Group, Immunogenetics Research Center, Mazandaran University of Medical Sciences, Sari, Iran
Abstract
Keywords
INTRODUCTION
In recent years, one of the most important applications of magnetic nanorods in diagnosing diseases, which are mainly done by biopsy [1], blood detection [2] and medical imaging [3] methods. These methods are unhelpful in the first stage of the disease, expensive and not easily accessible to many people [4-5]. So, we need to look for a method that is both cost-effective and also has the sensitivity and accuracy of the diagnosis. For this purpose, we use the interaction of magnetic nanorod with BSA aqueous solution in which the albumin is known as a diagnostic biomarker of kidney disease. The interaction of BSA with nanorods can be a model for designing a Magnetic nanobiosensor [6-7]. The magnetic nanobiosensor with fast, accurate and more efficient diagnosis would prevent much healthcare cost. This cost-effective and accurate diagnostic method with high sensitivity could also detect first signals of the disease [8]. In this paper, we discuss the synthesis and characterization of Hematite (α-Fe2O3) nanorods before and after interaction with BSA. Various methods were proposed for the synthesis of hematite nanorods, mostly based on chemical methods. Some of the most important ones include: thermal decomposition [9], wet chemical [10], hydrothermal [11], template mediated [12], hydrolysis [13], sol-gel [14] and co-precipitation [15-16]. Until recently, hydrothermal method was the most common approach for the synthesis of hematite nanorods [17-19]. In the present work, hydrothermal method was used in which CTAB acted as a surfactant agent at room temperature and interacted with hematite nanorods in BSA aqueous solution. Experimental analysis revealed that BSA would conjugate with inorganic molecules, binding in different directions and changing the morphology and optical properties of hematite nanorods after interaction [22-24].
MATERIALS AND METHODS
Materials
Iron (ш) chliride (FeCl3), sodium hydroxide (NaOH), Cetyl trimethylammonium bromide (CTAB), Phosphate-buffered saline (PBS), and bovine serum albumin(BSA) A9418-5G were all purchased from Sigma-Aldrich and used without further purification.
Synthesis of hematite nanorods
To synthesize hematite nanorods, 0.25 mol L-1 of FeCl3 solution was added into a beaker, followed by a dropwise addition of 8.5 mL of NaOH (2mol L−1) and 8.0 mL of deionized water (DIW) under vigorous magnetic stirring at room temperature. Similarly, in a separate beaker, CTAB of different concentrations (0.025, 0.05 and 0.1 mol L-1) was created. Two solutions were slowly mixed while stirring continuously. Then, the resulted transparent mixture was transferred to an autoclave with a capacity of 60 mL, where it was tightly sealed. The sample was heated to 150 °C and kept in an isothermal state for 6.0 h. Subsequently, the samples were cooled to room temperature naturally. The product was filtered and washed with deionized water for three times. PBS pill was solved in 200 cc of deionized water (DIW) to prepare PBS. It was then added to nanorod solution with the same volume of collected deionized water. To prepare the interaction, 0.4, 0.8, 1.6, 3.2 and 6.4 mg per mLconcentration of BSA to PBS solution and hematite nanorods were combined. The resulting interaction solution was saved for further analysis.
Materials Characterization
UV-visible spectroscopy of synthesized magnetic nanorods
Optical properties of hematite nanorods were evaluated using UV–Vis spectrophotometer (GBC Cintra 101), with DIW as dispersive medium. First, distilled water was added to two cuvettes regarded as reference and sample within the system. Scanning the baseline, the wavelength range was adjusted from 200 to 800 nm. In the next step, both reference and sample cuvettes were kept outside. The sample was diluted to 50% and then poured back into its cuvette. Then, it was put in the right place inside the device to be scanned from 200 to 800 nm.
X-ray powder diffraction of hematite nanorods
X-ray powder diffraction (XRD) pattern of as-prepared sample was measured using (GBC-MMA 007) X-ray diffractometer. The diffractograms were recorded with 0.02o step size i (speed of 10 deg/min) radiation over a 2θ range of 10 o –80 o.
FTIR spectroscopy of synthesized hematite nanorods
Potassium bromide was used as the background to measure FT-IR in 1730 Infrared Fourier Transform Spectrometer (Perkin-Elmer). First, the synthesized powder was completely mixed with potassium bromide since KBr would not be absorbed in the IR region. To make the pill ready to draw FTIR graph,a press device was used.
Energy Dispersive X-Ray Spectroscopy (EDS)
Energy Dispersive X-Ray Spectroscopy (EDS) analysis was used to determine the chemical composition, weight percent (Wt%) and atomic percent (At%) of the elements in each of the compounds (Mira 3-XMU).
Transmission electron microscopy of synthesized hematite nanorods
The morphology of solution samples without any changes in their preparation was examined by transmission electron microscopy (TEM, Philips CM30, 150 kV).
RESULTS AND DISCUSSION
Fig. 1 shows UV-Vis spectroscopy of hematite nanorods fabricated with different amounts of CTAB at room temperature (RT). CTAB could affect the shape of hematite nanostructures, causing the products to reach nanorod morphology. The sample prepared without CTAB could form nanoparticle structure (see Fig.1-a), with one peak located at 250 nm, and wavelength of 200–800 nm. However, regarding other amounts of CTAB (0.025, 0.05 and 0.1, mol L-1), the absorption band of hematite nanorods mainly located between 210-250 nm and 350-380 nm (see Fig.1, b-d), and CTAB could influence the formation of hematite nanorods. Figs. 2a-2c show optical absorption spectra of hematite nanorods prepared with constant amounts of CTAB and different volumes of DIW to obtain nanorods with more regular shapes. As can be seen, at 0.025 mol L-1 of CTAB with 5, 10 and 15 mL DIW, there were two sharp peaks around 250 and 420 nm in the visible region indicating that the product could exhibit the rod shape of hematite nanostructures.
Xia and colleagues [30] showed a possible relationship between UV-vis spectrum and morphology of nanostructures. The interaction between BSA protein and hematite nanorods would cause the peak at 300 nm to disappear, and the peak at 400 nm to show a red shift after adding BSA solutions of 0.4, 0.8, 1.6, 3.2 and 6.4 mg per ml (see Fig.3, b-f) concentrations. The interaction could change the structure of hematite nanorods due to the presence of a peak around 400 nm and the nanoparticles having spherical shape, which was in agreement with TEM microscopic analysed images.
XRD was used to study crystalline phase of the hematite nanorod powder. Fig. 4 shows XRD pattern of the powder obtained from 0.025 molof L-1 CTAB at RT. The sharp peaks would indicate that the crystal structure of hematite nanorods was related to (111), (220), (222), (311), (400), (422), and (511) Miller indices, corresponding to the formation of hematite phase based on the 73-0603 standard card [31]. The average size was calculated with Scherrer equation, according to which the full width at half maximum (FWHM) of peak 220 was about 15 nm [32,33]:
D=0.89λ/βcosθ (1)
Where λ = 0.154 nm, and θ is the reflection angle.
We used elemental analysis to prove the existence of iron element in the samples. Fig. 7 shows the Energy Dispersive X-Ray Spectroscopy (EDS) spectrum of hematite nanorods prepared with 0.025, 0.05 and 0.1 mol L-1concentration of CTAB and elemental analysis of hematite nanorods after interacting with BSA in concentrations of 0.4, 0.8 and 1.6 mg/ml. As can be seen in the insert of Fig. 7, the results indicated the presence of Fe and O in the hematite samples. The sample with 0.8 mg/ml of BSA have more Wt% of Fe than samples with 0.025, 0.05 and 0.1 mol L-1concentration of CTAB.
TEM helped to obtain more morphological details of nanostructures. Figs. 8a-8c show TEM images of hematite nanorods prepared with 0.025, 0.05 and 0.1 mol L-1concentration of CTAB, and their distribution using Digimizer software. The results showed the formation of uniform nanorod structures. The average length of hematite nanorods in TEM images was calculated using Digimizer software. The distribution graph of nanorods is presented in Figs. 10a-10c. As shown in Fig. 10, the average lengths of hematite nanorods were about 25-30, 50-55and 25-30 nm in 0.025, 0.05 and 0.1 mol L-1concentration of CTAB, respectively.
Fig. 9 shows TEM images of hematite nanorods after interacting with BSA. On average, the surface charge of CTAB was positive, but in albumin the surface charge was negative. Both positive and negative charges interacted electrostatically. When protein concentration was more than CTAB, electron microscope images of samples showed changes in morphology and aggregation of the nanorods.The averagelengths of hematite nanorods were about 25-30, 5-50and 30-40 nm at 0.4 mg/ml, 0.8 mg/ml and 1.6 mg/ml concentration of BSA, respectively.
CONCLUSION
Hematite (α-Fe2O3) nanorods were synthesized using hydrothermal method with CTAB as a surfactant agent at different molar ratios. The interaction between BSA protein and hematite nanorods could affect the morphology and optical properties of hematite nanostructures. The size and shape of hematite nanorods could change with different amounts of BSA solution at room temperature. UV-vis spectroscopy revealed two main peaks before interaction, which showed the formation of nanorods. While adding BSA protein solution to nanorods, peaks disappeared and optical properties of samples changed. In addition, the microscopic technique parallel to absorption spectroscopy could confirm the formation of hematite nanorods and their spherical shape after interacting with BSA protein.
CONFLICT OF INTERESTS
The authors declare that there is no conflict of interests regarding the publication of this paper.